<wbr id="0p4dr"><legend id="0p4dr"></legend></wbr>
  • <wbr id="0p4dr"></wbr>

  • <sub id="0p4dr"><listing id="0p4dr"></listing></sub>
    <form id="0p4dr"><span id="0p4dr"><track id="0p4dr"></track></span></form>

    <sub id="0p4dr"></sub>
    <form id="0p4dr"></form>
    1. 無線智能家居無線空氣質量探測器智能家居
      無線智能家居無線空氣質量探測器智能家居
      產品價格:¥1(人民幣)
    2. 規格:標準
    3. 發貨地:江蘇省南京市
    4. 品牌:
    5. 最小起訂量:1臺
    6. 免費會員
      會員級別:試用會員
      認證類型:企業認證
      企業證件:通過認證

      商鋪名稱:南京物聯傳感技術有限公司總部

      聯系人:唐勤強(先生)

      聯系手機:

      固定電話:

      企業郵箱:tangqq@wulian.mobi

      聯系地址:上海市 楊浦區 逸仙路135號

      郵編:200082

      聯系我時,請說是在焊材網上看到的,謝謝!

      商品詳情

        無線空氣質量探測器

        WL-AQD-A01這款產品專門用于檢測室內空氣質量。將它安裝在家庭中臥室內,它能夠測量相關的CO2、溫度、濕度、VOC 的水平,可以控制設備以保證優良的生活環境。

           
        主要特點
         
        -監測室內多種空氣參數,包括CO2、溫濕度和VOC;
         
        -尺寸小巧,價格便宜;
         
        -能自動控制空調等設備。
         
        產品描述
         
             變送器適合測量室內空氣質量。將該產品安裝在家庭或臥室,可以用于測量空氣中的CO2、溫度、濕度和
         
        VOC 的水平,自動控制凈化通風設備運轉保持室內優良的環境。也可以在已有或待安裝的通風系統中以較低
         
        的成本安裝該設備。
         
        變送器集成了4 個傳感器,可同時測量CO2、溫度、濕度和VOC,體積小巧,價格便宜。通過RS485 和
         
        RS232接口輸出測量數據,監測各點空氣質量變化情況,實現智能控制空調、加濕機和其他通風設備運轉。
         
        主要參數
         
         
        工作參數
        工作溫度范圍
        0 ~ 50
        工作濕度范圍
        0 ~ 95%RH
        儲存溫度范圍
        -20 ~ 60
        電源輸入
        DC 12V
        電流消耗
        平均值為50mA,峰值為600mA
        信號輸出
        RS-485, RS-232 (TX only)
        尺寸
        75W x 120H x 22D (mm)
        CO2 檢測
        檢測方法
        NDIR
        測量范圍
        0~2,000ppm / 0~5,000ppm / 0~10,000ppm(可選)
        檢測精度
        ±30ppm±5%讀數(0 ~ 50℃)
        采樣時間
        3 秒
        響應時間(90%)
        30 秒
        溫度測量
        測量范圍
        -20 ~ 60
        精度
        ±1℃
        濕度測量
        測量范圍
        0 ~ 95%RH
        精度
        ±5%RH
        VOC測量
        檢測氣體
        TVOC, HC 等
        檢測方法
        半導體技術
         
        WL-AQD-A01 Protocol
         
        1.  WL-AQD-A01 Protocol
          
            WL-AQD-A01 supports RS232 and RS485
         
         
        2.  Communication Parameter Setting
         
         
        Parameter
        Description
        Baud rate
        9600BPS
        Data Bit
        8 bits
        Parity Bit
        None
        Stop Bit
        1
        Flow control
        None
         
        3. RS232 Protocol
         
           Data transmission : AQM sends data to host every 3 seconds automatically.
           Data packet : Refer to the data packet defined in RS485 data packet.
         
         
        4. RS485 Protocol
         
        4-1. Network Configuration (Multi-drop topology)
         
          
        4-2. Data Handshaking Sequence
          Slave(WL-AQD-A01) sends data to host upon request via RS485 line.
         
          
        * Reply delay : 10mS
        4-3. Packet Definition
         
             ENQ Packet
         
         
        ENQ
        ID
        CSUM
        ETX
        0xF5
        0xFC
        -
        -
        0x05
        B0        B1         B2        B3         B4
         
         
        Field
        Name
        Value
        STX
        Start code
        0xFA 0xF0
        ID
        ID
        0x00 ~ 0xFF
        CONF
        Device Configuration
        If bit is set, corresponding
        sensor is installed.
        Bit0 : VOC sensor
        Bit1 : Humidity sensor
        Bit2 : Temperature sensor
        Bit3 : CO2 sensor
        B4~Bit7 : 0x00
        CO2
        CO2 Concentration, PPM
        2 byte integer value
        If reading is 450 then actual
        CO2 concentration is 450ppm.
        TEMP
        Temperature, ℃
        2 byte integer value
        Temp = value/10
        If reading is -103 then actual
        temperature is -10.3 .
        HUMD
        Humidity, %
        1 byte integer value
        Temp = value/10
        If reading is 75 then actual
        humidity is 75%.
        VOC
        VOC
        0x00 : Normal
        0x10 : High
        0x40 : Very High
        CSUM
        Checksum
        Check Sum = Low byte of sum(B0
        + B1 … + B9)
        ETX
        End of code
        0x05
      在線詢盤/留言
    7. 0571-87774297  
      91精品国产综合久久婷婷