IEC60950-1&GB4943.1信息技術類設備檢測實驗室配置清單-焊材網資訊-歡迎光臨焊材網-chinahancai.com

今日最新資訊

熱門資訊

IEC60950-1&GB4943.1信息技術類設備檢測實驗室配置清單

發布者：東莞市高升電子精密科發布時間：2018-01-24 09:27:00 訪問次數：291

IEC60950-1&GB4943.1信息技術類設備檢測實驗室儀器設備推薦清單：

SAR 測試

手機性能測試

EMC暗室測試

序號	條款號	檢測內容	所需檢測儀器設備	精度要求和量程要求	所需檢測儀器、設備
序號	條款號	檢測內容	所需檢測儀器設備	精度要求和量程要求	設備名稱	設備型號	設備量程	設備精度
3	1.6.2	Input Current	Amp-meter		數字功率計	WT310	0—500V 0—20A 0—10kW	?1.5%
4	2.1.1.1	Access to energized parts	Test finger (joint /rigid 30N, fig. 2A)	See fig. 2A	關節試驗指	GS-IP100	fig. 2A	fig. 2A
5				See fig. 2A	直型試驗指	GS-IP11	fig. 2A	fig. 2A
6					推拉力計	ANF-50	0—50N	?1N
7			Test pin (fig. 2B 4mm/3mm/15 mm long)	See fig. 2B	試驗銷	GS-IP03	fig. 2B	fig. 2B
8			Test probe (fig. 2C 12mm/80mm)	See fig. 2C	試驗探頭	GS-IP05	fig. 2C	fig. 2C
9	2.1.1.5	Energy Hazard	Variable resistive load		電子負載	3250	AC/DC 0-60V 0-20A 0-300W	?1.5%
10	2.1.1.7	Plug discharge	Measuring instrument with input impedance 100MΩ ?5 MΩ in parallel with an input capacitance of 25pF or less.		示波器	F196C	2mV-100V/div 5ns-5s/div 100M	?0.2%
11	2.1.1.7	Plug discharge			高壓探棒	N2771A	0-10kV	?1%
12	2.1.1.9	Audio Amplifiers	Suitable signal generator and audio power measuring equipment		噪聲信號發生器	DF1681	20-20kHz 0-70dB	?1dB
13	2.1.1.9	Audio Amplifiers			音頻信號發生器	GAG-810	10-1000kHz	?1.5%
14	2.3.1	Limits of TNV circuits	Resistor 5000Ω ? 2%,	?2%	試樣電阻	5kΩ	5000Ω	?0.3%
15	2.3.4	Connection of TNV circuits to other circuits	Resistor 5000Ω ? 2%,	?2%	試樣電阻	5kΩ	5000Ω	?0.3%
16	2.3.5	Test for operating voltages generated externally	Test generator	120V? 2V a.c., 50 or 60 Hz, 1200Ω ? 2%	試驗電壓發生器	GS-TNV10	0-240V 50 or 60 Hz 1200Ω	?1%
17	2.4.2	Limited current circuits, limit values	Resistor 2 000 Ω ? 10%,	? 10%	試樣電阻	2kΩ	2000Ω	?0.5%
18	2.4.2	Limited current circuits, limit values	Capacitance measuring device		LCR測量儀	4263B	10μH-1H 1pF-1μF 0.1Ω-100kΩ	?0.1%
19	2.6.3.4	Resistance of earthing conductors	High current source with a voltage not exceeding 12 V		接地電阻測試儀	TOS6210	0—0.2Ω	?0.002Ω
20	2.9.2	Humidity conditioning	Chamber (91% Rh...95% Rh, 20...30 ? C)		調溫（調濕）箱	GS-TH800	-40—150℃ 0-95%RH	?2℃，?2.5%RH
21	2.10	Creepage distance/clearance/distance through insulation (determination of requirements; working voltage measurements)	Oscilloscope		示波器	F196C	2mV-100V/div 5ns-5s/div 100M	?0.2%
22		Creepagedistance/clearance/distance through insulation (measurements)	Dial gauge		爬電距離測試卡	CC-23	1.0—8.0mm	0.1mm
23			Micrometer		游標卡尺	150mm	0—150mm	0.02mm
24			Microscope		讀數顯微鏡	Vibao	0-100mm	?0.05mm
25	2.10.3.9	Measurement of transient levels	Test-generator; reference 2 of table N.1		脈沖發生器	1950S	脈沖波形：1.2?50μs電壓：0-7KV	?5%
26	2.10.3.9	Measurement of transient levels	Test-generator; reference 2 of table N.1		脈沖發生器	1950S	脈沖波形：10?700μs電壓：0-7KV	?5%
27	2.10.4	Creepage distances	Test equipment for tracking		漏電起痕試驗裝置	GS-TK20	0-600V 0-1A	?1%
29	2.10.9 & 2.10.10 & 2.10.11 (and 2.10.8.2)	Thermal cycling and thermal ageing	Full draught oven (? 2?C) Cooling facility (0? C)	? 2?C	調溫（調濕）箱	GS-TH800	-40—150℃ 0-95%RH	?2℃，?2.5%RH
30	2.10.8.4	Abrasion resistance test	Scratch test device with steel pin	20mm/s; 10?0.5N, 80~85?	耐劃痕試驗儀	GS-NH300	20mm/s;10?0.5N, 80~85?	?2%
31	2.10.8.4	Abrasion resistance test	Scratch test device with steel pin	頂角40度，倒圓半徑0.25mm?0.02mm	鋼針	\	頂角40度，倒圓半徑0.25mm?0.02mm	?1degree，?0.02mm
32	2.10.7	Enclosed and sealed parts	See 2.10.9 & 2.10.10	? 2?C	調溫（調濕）箱SETH-Z-061LK	GS-TH800	-40—150℃ 0-95%RH	?2℃，?2.5%RH
33	3.1.5, 3.1.9 and 4.2.2	10 N steady force test	Suitable tool for applying steady force of 10 N /- 1N	?1N	推拉力計	ANF-50	0—50N	?1N
35	3.2.6	Cord anchorage and strain relief	Appropriate weights		電源線拉扭試驗機	GS-DXLN20	0-50kg	?1%
36	3.2.8	Cord guards	Appropriate weights		推拉力計	ANF-50	0—50N	?1N
37	4.1	Stability	Inclined plane 10?		傾斜平臺	GS-QX800	0-15?	?3%
38			Force 250N		推拉力計	ZP-1000	0-1000N	?0.2%
39			Test tool 800N with a flat surface 12,5cm by 20cm		推拉力計	ZP-1000	0-1000N	?0.2%
40			Test tool 800N with a flat surface 12,5cm by 20cm		金屬平面	136	12,5cm by 20cm	?0.5%
41	4.2.3	Steady force test 30 N	Test finger (rigid 30N? 3N, fig. 2A)		直型試驗指	GS-IP11	fig. 2A	fig. 2A
42	4.2.3	Steady force test 30 N	Test finger (rigid 30N? 3N, fig. 2A)		推拉力計	ANF-50	0—50N	?1N
43	4.2.4	Steady state force, 250 N	Test tool 250N? 10N with a circular plan surface ? 30mm.		推拉力計	ZP-1000	0-1000N	?0.2%
44	4.2.4	Steady state force, 250 N	Test tool 250N? 10N with a circular plan surface ? 30mm.		金屬平面	GS16	? 30mm	?0.1mm
45	4.2.5	Impact test	? 50mm/500g? 25g steel ball	500g? 25g	沖擊鋼球	GS-IP07	500g ? 50mm	10g， 0.004mm
46	4.2.6	Drop test	Hard wood 13mm on 19mm to 20mm plywood, two layers		跌落平臺	GS207	/	/
47	4.2.7	Stress relief	Oven 70K over normal temp		高溫試驗箱	GS-GW005	室溫—200℃	?1℃
49	4.2.10	Wall or ceiling mounted equipment	Several weights		推拉力計	ZP-1000	0-1000N	?0.2%
50	4.3.2	Handles and manual controls	Force 15N/20N/30N/50N		推拉力計	ANF-50	0—50N	?1N
51	4.3.6	Direct plug-in equipment	Test equipment (see Fig. 11 of IEC 60065)		插頭力矩測試儀	GS-CTN04	0-0.25Nm	?1%
53	4.3.13.2	Ionizing radiation	Ionization meter (Annex H)		電離輻射計	440RF/D	0-1000μSV/h	?20%
57	4.4	Protection against hazardous moving parts	Test finger (joint /rigid 30N, fig. 2A)	See fig. 2A	關節試驗指	GS-IP100	fig. 2A	fig. 2A
58				See fig. 2A	直型試驗指	GS-IP11	fig. 2A	fig. 2A
59					推拉力計	ANF-50	0—50N	?1N
60	4.5	Thermal requirements
61		Voltage supply	Single phase voltage supply systems/variability/adequacy		變頻電源	6902	0-300V 0-15A	?1.5%
62		Voltage supply	Three phase voltage supply systems		變頻電源	AFR-360	60kVa	?1.5%
63		Temperature (rise)	Temperature recorder (multi-channel)		記錄儀	DR232-02-00-1R	0—300℃	?0.5℃
64			Thermocouples		熱電偶	TT-K-30	0—150℃	?0.5℃
65			Winding resistance (normally > 1,0 Ω 2-wire, 4-wire<1,0 Ω ).		數字多用表	34401A	0.1-100MΩ	?3%
66		Voltage	Voltmeters (ac/dc)		數字多用表	34401A	0—1000V	?1%
67		Voltage	High voltage meter (probe)		高壓探棒	N2771A	0-10kV	?1%
68		Current	Currents (ac/dc)		數字功率計	WT310	0—500V 0—20A 0—10kW	?1.5%
69		Loading	Loads (resistive)		電子負載	3250	AC/DC 0-60V 0-20A 0-300W	?1.5%
70	4.5.5	Resistance to abnormal heat	Ball pressure test apparatus according to IEC 60695-10-2 Oven at least 125?C	球直徑：5mm；砝碼：20N?0.2N	球壓試驗裝置	GS-QY21	球直徑：5mm；砝碼：20N	?0.2N
71	4.5.5	Resistance to abnormal heat			高溫試驗箱	GS-GW005	室溫—200℃	?1℃
72	4.6.2	Bottoms of fire enclosure	Distillate fuel oil as described in Annex A.3.2	10ml 1ml/s	灼熱燃油	GS-ZRY06	10ml 1ml/s	?0.2ml ?0.1ml/s
73	4.6.4.2	Evaluation of larger openings	Suitable tool (or tools) to simulate a straight metal object, 1mm in diameter, length up to 13 mm	? 1mm	試驗探針	GS-IP14	? 1mm	0.044mm
74	4.6.5	Adhesives for constructional purposes	Oven up to 100 ? C		高溫試驗箱	GS-GW005	室溫—200℃	?1℃
75	4.7.3	Materials, Tests see Annex A	V-1, V-2, HF-2, 5V	IEC60695	針焰試驗儀	GS-NF30	IEC60695	IEC60695
76			Bunsen burner (9,5 ? 0,5 mm)	IEC60695	UL94水平垂直燃燒試驗儀	GS-HVUL20	IEC60695	IEC60695
77			Gas for burner (~37 MJ/m3)		甲烷氣體	98%純度以上	/	/
78			Oven for preconditioning		高溫試驗箱	GS-GW005	室溫—200℃	?1℃
79	4.7.3.6	Materials used in high-voltage components	Test of Annex A or test of 14.4 of IEC 60065 or needle flame test according to IEC 60695-2-2	IEC60695	針焰試驗儀/水平垂直燃燒儀	GS-NF30\GS-HVUL20	IEC60695	IEC60695
80	5.1	Touch current and protective conductor current	Measuring instruments of Annex D		泄漏電流測試儀	Simpson228	0-10mA	?1%
81	5.2	Electric strength	Test equipment with the relevant voltage and tripping current	短路電流>200mA	AC/DC耐壓絕緣測試儀	TOS9201	AC:0-5kV， 0—110mA; DC:0-6kV, 0-10mA; 短路電流>200mA	?1%
83	6.2.1	Protection of equipment users from overvoltages on telecommunication networks	Test probe (Fig. 2C, 12mm/80mm)	See fig. 2C	試驗探頭	GS-IP05	fig. 2C	fig. 2C
84	6.2.2.1	Impulse Test	Impulse test generator according to Annex N		脈沖發生器	1950S	脈沖波形：10?700μs電壓：0-7KV	?5%
85	6.2.2.3	Protection of equipment users from overvoltages on telecommunication networks	insulation resistance		絕緣電阻測試儀	TOS7200	0-1000V 0-2000MΩ	?0.5%
86	7.4.2	Voltage surge test	Test generator reference 3 of table N.1		浪涌測試儀	SUG10/700G	0-10kV	?5%
87	7.4.3	Impulse test	Test generator reference 1 of table N.1		脈沖發生器	1950S	脈沖波形：10?700μs電壓：0-7KV	?5%

來源：東莞市高升電子精密科

免責聲明：焊材網轉載作品均注明出處，本網未注明出處和轉載的，是出于傳遞更多信息之目的，并不意味著贊同其觀點或證實其內容的真實性。如轉載作品侵犯作者署名權，或有其他諸如版權、肖像權、知識產權等方面的傷害，并非本網故意為之，在接到相關權利人通知后將立即加以更正。聯系電話：0571－87774297。